iPhone 7 Teardown and Reassemble Guide – Fixez.com

https://www.fixez.com presents the main iPhone 7 Screen Replacement, Teardown and also Reassemble Guide. This detailed fixing video clip will certainly reveal you the best ways to fix a busted or damaged apple iphone 7 4.7″ display assembly, and exactly how to entirely teardown as well as reconstruct your Apple phone. Browse through Fixez.com for all of the DIY iPhone 7 replacement tools, screens and components you require to swiftly, and economically, repair your tool!

https://www.fixez.com/store/iphone/iphone-7
https://www.fixez.com/categories/repair-tools

Subscribe to our YouTube Channel for extra DIY smart device and also tablet teardown and repair videos! https://www.youtube.com/channel/UCDJrZCUtdJQaJq0akRCt3Ng
Like us on Facebook: https://www.facebook.com/fixez.com
Follow us on Twitter: https://twitter.com/fixezdotcom

apple iphone 7 Screen Repair, Teardown and also Reassemble Guide Video:

Action 1 – Power down your Apple iPhone 7 phone.

Step 2 – Eject the Nano-SIM Card Tray.

Tip 3 – Remove the two lower 3.4 mm Pentalobe screws situated next to the lightning connector.

Tip 4 – Use the precision knife to produce enough area to insert a triangle opening device. With the triangular opening tool slice with the sticky adhesive and meticulously decouple the apple iphone 7 display setting up from the rear instance. Unlike previous apple iphone models, the iPhone 7 opens similar to a book, along the side rather than on top. The display screen assembly is still connected to the apple iphone by cords along the middle-right side, so don’t aim to eliminate it entirely simply yet. Get rid of the following 4 Tri-Point screws safeguarding the brace that covers the battery port as well as two of the display cables. These screws are different sizes, so be certain to keep in mind where they go. With the bracket out of the method spudge up the cords from the reasoning board. Eliminate the adhering to 2 Phillips screws that safeguard the bracket covering the top component screen cable. Separate the cable television as well as complimentary the iPhone 7 screen assembly from the phone.

Tip 5 – Remove the adhering to 6 Phillips screws, complied with by the steel clip they safeguard in place. Use the tweezers to assist remove the tangled up 7-megapixel apple iphone 7 Front-Facing Camera Cable Assembly.

Step 6 – Remove the following 4 Tri-Point screws and afterwards the metal brace. Dividing the solid state apple iphone 7 Plus home switch is simple, with just light adhesive on the wire and also no delicate gasket.

Step 7 – Remove the complying with 6 Tri-Point screws. Utilize the spudger to launch the adhesive from below the base of the apple iphone 7 LCD shield plate.

Tip 8 – In location of the earphone jack is a barometric air vent. Get rid of the complying with 2 Phillips screws then lift it out of the apple iphone 7 back situation. Detach the Taptic Engine from the logic board. Remove the adhering to 3 Phillips screws and tweeze out the apple iphone 7 Taptic Engine. This sleek engine uses haptic feedback to replicate the push of a button.

Slowly and carefully draw each strip up and away from the apple iphone 7. And also just like that, out pops the 1960 milliampere-hour (mAh), 3.8-volt apple iphone 7 battery.

Step 10 – Remove the adhering to 2 Phillips screws. Get rid of the safety metal cover. With the spudger in hand, separate the 12-megapixel iPhone 7 rear-facing cam and tear it out of the chassis.

Step 11 – Remove the adhering to 4 Phillips screws. Pluck out the top left Wi-Fi antenna. Prior to excavating the iPhone 7 logic board out of the back situation, it is essential to strike a bevy of Phillips, Tri-Point, and also standoff screws, and dispatch of a few adapters. After taking treatment of the last 2 adapters, thoroughly uproot the apple iphone 7 reasoning board from the back situation.

Action 12 – Remove the following 4 Phillips screws. Remove the iPhone 7 speaker.

Tip 13 – Remove the adhering to 5 Phillips screws. The iPhone 7 Lightning adapter setting up is moderately adhered to the back instance, but with a little spudgering it is conveniently gotten rid of.

Step 14 – Remove the adhering to 2 Phillips screws. Essence the antenna flex wire, which works as a bridge between antenna paths. Eliminate the standoff screw, and after that the bracket. Eliminate the following 5 Phillips screws. The last part to surrender is a cable range which contains the power as well as quantity switch switches over, LED flash, a microphone, and the ring/ silent button.